全文获取类型
收费全文 | 99篇 |
免费 | 21篇 |
国内免费 | 17篇 |
专业分类
航空 | 114篇 |
航天技术 | 8篇 |
综合类 | 7篇 |
航天 | 8篇 |
出版年
2023年 | 5篇 |
2022年 | 7篇 |
2021年 | 7篇 |
2020年 | 8篇 |
2019年 | 6篇 |
2018年 | 4篇 |
2017年 | 9篇 |
2016年 | 19篇 |
2015年 | 5篇 |
2014年 | 5篇 |
2013年 | 3篇 |
2012年 | 5篇 |
2011年 | 6篇 |
2010年 | 1篇 |
2009年 | 7篇 |
2008年 | 4篇 |
2007年 | 5篇 |
2006年 | 1篇 |
2005年 | 5篇 |
2004年 | 6篇 |
2003年 | 4篇 |
2002年 | 2篇 |
2000年 | 2篇 |
1999年 | 4篇 |
1998年 | 2篇 |
1995年 | 1篇 |
1994年 | 3篇 |
1992年 | 1篇 |
排序方式: 共有137条查询结果,搜索用时 78 毫秒
41.
叙述了如何将声发射技术应用于航空铝合金的高速铣削过程监测,介绍了监测装置硬件系统和信号数据采集平台的构成,最后运用小波分析进行信号分解,计算分解后的各频段能量,并从频段的能量对比中发现,信号能量可以作为刀具磨损的特征参数. 相似文献
42.
为研究干涉配合中被连接件最小截面(SCS)所传递载荷(截面载荷)的幅值得以降低的原理,按一定规律对销钉与板进行分区,并将其用同等刚度的弹簧代替,建立了销钉干涉配合的弹簧分析模型,进而从弹性角度解释了干涉配合中板的最小截面所传递载荷的幅值得以降低的原因。基于该模型分析了静载下截面载荷随外载的变化规律,得到了循环载荷下截面载荷幅值与外载幅值间的关系,其与有限元分析(FEA)结果之间的最大误差不到20%。分析发现:连接件与被连接件间的接触力随外载变化的自动调节作用是截面载荷幅值降低的原因;对于特定的绝对干涉量,干涉配合只对一定范围内的外载具有调节作用。当外载在干涉配合的有效影响区时,截面载荷幅值的降低程度完全决定于连接件与被连接件的相对刚度;若外载过大使得钉孔发生分离,干涉配合不仅对载荷幅值不再具有调节作用,还容易引起钉孔接触面的微动磨损。 相似文献
43.
44.
45.
《中国航空学报》2021,34(2):358-375
In this paper, the flow characteristics of the double wall structure are presented and the effect of the broken pin size on the cooling performance and flow field of the double wall configuration is investigated. A periodic plate model with seven units is adopted, and there are an impingement hole and a film hole in each unit. Under five blowing ratios, six different sizes of the broken pin are compared, and the double wall configuration without broken pins is taken as the baseline. The results show that if the broken pins height is too small, the cooling effectiveness usually cannot be improved. With the presence of broken pins with a height of more than 0.4, the effectiveness is improved due to the enhancement of reattachment and recirculation of coolant. With the increase of the broken pin height, the cooling effectiveness increases. However, the increase of the diameter does not always improve the cooling performance, since the limiting effect of the wall jet. In this study, Case 6 with the largest broken pin always has the best cooling performance, but also the largest flow resistance. In Case 6 temperature is reduced by almost 15 K compared to the baseline, and more areas have relatively higher cooling effectiveness. 相似文献
46.
多钉连接件钉传载荷计算的一个解析方法 总被引:9,自引:0,他引:9
对多钉连接件钉传载荷的计算问题提出了一个解析分析方法,推导了求解钉载的线性代数方程组并给出了若干算例。该方法使用方便,并具有工程分析所要求的精度。 相似文献
47.
搅拌头形状对焊缝塑化金属流动行为的影响 总被引:2,自引:0,他引:2
本文研究了搅拌形状对焊接过程中焊缝塑化金属流动行为的影响,使用了4种形式的搅拌头,(a)带反螺纹的圆柱形搅拌头,(b)带正螺纹的圆柱形搅拌头,(c)带反螺纹的圆锥形搅拌头,(d)带反螺纹的凸轮形搅拌头。研究结果表明,焊接过程中,焊缝塑化金属存在三种运动:表层的水平圆周运动、探针周围的螺旋运动、塑化环外围的刚塑性运动。搅拌头形状是影响焊缝塑化金属流动形态的主要因素。搅拌头探针表面的螺纹旋转方向不同,塑化金属的受力状态不同,探针周围金属朝上或朝下螺旋运动,从而带动周围金属流动;探针形状不同,可以改变塑化金属的流动性。 相似文献
48.
49.
50.
采用复变-变分法求解受钉传载荷含边缘裂纹各向异性与各向同性板的应力强度因子。首先建立满足所有各向异性弹性力学基本方程和钉孔合力平衡条件及位移单值条件的应力和位移级数表达式,然后应用变分原理满足板的边界条件,从而确定应力强度因子。计算表明,级数收敛迅速,数值解和实验结果吻合,而所需机时较少。 相似文献